Manufacturer | Bently Nevada |
Model | 3500/22M |
Order Code | 138607-01 |
Catalog | 3500 |
Description | Bently Nevada 3500/22M 138607-01 Transient Data Interface |
Ordering Information
For the detailed listing of country and product specific approvals, refer to the Approvals Quick Reference Guide (108M1756) available from
Bently.com.
3500/22M TDI Module and I/O
3500/22-AA-BB-CC
A: Transient Data Interface Type
01 Standard (use for standard monitoring applications)
B: I/O Module Type
01
10Base-T/100Base-TX Ethernet
02
100Base-FX (Fiber Optic) Ethernet
03
10Base-T/100Base-TX Ethernet with gold
plated OK Relay contacts
04
100Base-FX (fiber optic) Ethernet with gold
plated OK Relay contacts
C: Agency Approval
00
None
01
CSA/NRTL/C (Class 1, Division 2)
02
Multi (CSA, ATEX, IECEx)
3500 22M Dynamic Data Enabling
Disk
This disk enables the number of channels of dynamic data (i.e., the ability to collect
waveforms) that the TDI will support. There are two levels of dynamic data. Steady-State points are channels that collect waveform data due either to a software command or to an alarm event, and therefore support current values, scheduled waveform capture, and alarm data capture. Transient points provide all the function of a Steady-State point with the additional capability of waveform collection due to parameter variations such as machine speed.
3500/09-AAA-BBB
A: Steady-State Points
000 to 672
Steady-State Points
B: Transient Points
002 to 672
Transient Points
The sum of the two fields must be equal
to or less than 672. One disk can support
multiple TDIs.
Ethernet Cables
Standard 10 Base-T/100 Base-TX Shielded
Category 5 Cable with RJ-45 connectors (solid
conductor)
138131-AAA
A: Cable Length
006
6 feet (1.8 m)
010
10 feet (3.0 m)
025
25 feet (12.2 m)
040
40 feet (12.2 m)
050
50 feet (15.2 m)
075
75 feet (22.9 m)
085
85 feet (25.9 m)
100
100 feet (30.5 m)
120
120 feet (36.6 m)
150
150 feet (45.7 m)
8/11
3500/22M Transient Data Interface Module
Datasheet
161581 Rev. U200
200 feet (61.0 m)
250
250 feet (76.2 m)
320
320 feet (97. m)
Standard lengths for 10Base-T/100Base
TX cabling are shown above.
Fiber Optic Cable
100 Base-FX fiber optic cable with MT-RJ female
connectors.
161756-AAA
A: Cable Length in feet up to 1300 ft (400m)
010 to 500
10 ft. to 500 ft. in 10 ft. increments
only
500 to 1300 500 ft. to 1300 ft. in 100 ft. increments
only
Spares
288055-01
Standard Transient Data Interface
Module with USB cable
123M4610*
10 foot A to B USB cable
146031-01
10Base-T/100Base-TX I/O Module
146031-02
100Base-FX (Fiber Optic) I/O Module
161580
3500/22M TDI Operation and
Maintenance User Guide
164466
Network Accessories Datasheet
00580441
Connector header, internal
termination, 3-position, green
00580436
Connector header, internal
termination, 6-position, green
111M5777
Connector header, internal termination, 2-position, green
* The USB cable part number is 123M4610.
This specific cable is required to maintain isolation between chassis and ground. It is
also important that the computer being attached to the USB needs to be operating
from batteries (i.e. NOT connected to ground) to avoid creating a ground loop.
Description
The 3500/22M Transient Data Interface (TDI) is the interface between the 3500 monitoring system and compatible
software (System 1 Condition Monitoring and Diagnostic software and 3500 System Configuration software). The TDI combines the function of a 3500/20 Rack Interface Module (RIM) with the data collection capability of a communication processor such as TDXnet.
The TDI resides in the slot adjacent to the power supplies of a 3500 rack. It interfaces with M series monitors (3500/40M, 3500/42M, etc.) to continuously collect steady state and transient dynamic (waveform) data and pass this data through an Ethernet link to the host software. Refer to the Compatibility section at the end of this document for more information.
Static data capture capability is standard with the TDI.
However, using an optional Channel Enabling Disk will allow the TDI to capture dynamic and high-resolution transient data as well. The TDI incorporates the communication
processor function within the 3500 rack.
Although the TDI provides certain functions common to the entire rack, it is not part of the critical monitoring path and has no effect on the proper, normal operation of the overall monitor system for automatic machinery protection. Every 3500 rack requires one TDI or RIM, which always occupies Slot 1 (next to the power supplies).